http://www.articca.com/blog/攻絲機_氣動攻絲機_電動攻絲機 - RainbowSoft Studio Z-Blog 1.8 Walle Build 100427zh-CNCopyright 石家莊力仕達工貿有限公司 . Some Rights Reserved.Fri, 20 Sep 2024 11:40:04 +0800a@b.com (admin)http://www.articca.com/blog/post/ShuKongGongSiJi.htmlThu, 01 Dec 2011 21:36:09 +0800http://www.articca.com/blog/post/ShuKongGongSiJi.html數控攻絲機

]]>電動數控攻絲機Ⅱ http://www.articca.com/blog/post/ShuKongGongSiJi.html#commenthttp://www.articca.com/blog/http://www.articca.com/blog/feed.asp?cmt=212http://www.articca.com/blog/cmd.asp?act=tb&id=212&key=ad3a01b7a@b.com (admin)http://www.articca.com/blog/post/WanXiangTou.htmlThu, 01 Dec 2011 21:34:00 +0800http://www.articca.com/blog/post/WanXiangTou.html萬向頭

]]>電動數控攻絲機Ⅱ http://www.articca.com/blog/post/WanXiangTou.html#commenthttp://www.articca.com/blog/http://www.articca.com/blog/feed.asp?cmt=209http://www.articca.com/blog/cmd.asp?act=tb&id=209&key=1b92a381a@b.com (admin)http://www.articca.com/blog/post/SKXFGSPII-DuTeXianShiPing.htmlThu, 29 Sep 2011 20:58:50 +0800http://www.articca.com/blog/post/SKXFGSPII-DuTeXianShiPing.html “力仕達”牌電動數控懸浮攻絲機，采用220V單相交流伺服電機,4.3吋觸控式顯示屏,定扭輸出無級調速,精準控制攻絲深度.先進的技術,完美的服務保障.必將給您帶來全新品質,全新效率,全新的感受. 獨特的觸控式顯示屏使您的工作變得輕松自如，接通電源后，旋轉電源開關至開的位置，觸控屏顯示主畫面。用手指輕觸顯示屏開始鍵，出現各畫面模式，用手指輕觸速度畫面，進行速度參數設定，用手指輕觸位置畫面，進行位置控制參數設定即定深攻絲…… ...

]]>電動數控攻絲機Ⅱ http://www.articca.com/blog/post/SKXFGSPII-DuTeXianShiPing.html#commenthttp://www.articca.com/blog/http://www.articca.com/blog/feed.asp?cmt=44http://www.articca.com/blog/cmd.asp?act=tb&id=44&key=a64461d2a@b.com (admin)http://www.articca.com/blog/post/SKXFGSPIIGongSiJi.htmlThu, 29 Sep 2011 20:58:01 +0800http://www.articca.com/blog/post/SKXFGSPIIGongSiJi.html · M3-M24 · M3-M36 · 垂直或垂直水平兩用（4*90°） · 最大回轉半徑1100毫米 · 七檔減速模塊針對各種材質、所攻螺紋的大小提供不同的扭矩/轉速模塊，兼顧力矩與速度的最佳配比，最大程度的提高效率。

]]>電動數控攻絲機Ⅱ http://www.articca.com/blog/post/SKXFGSPIIGongSiJi.html#commenthttp://www.articca.com/blog/http://www.articca.com/blog/feed.asp?cmt=43http://www.articca.com/blog/cmd.asp?act=tb&id=43&key=b03b5adc